Understanding Plumber's Essentials for Bathtub Installation
Understanding Plumber's Essentials for Bathtub Installation
Blog Article
Just how do you feel when it comes to Tools You Need to Install a New Bathtub ?

Installing a bath tub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bath tub with a new one is likewise a moderately challenging task. If the old bathtub is readily easily accessible, the project can relocate rapidly; if you need to open a wall to eliminate the old bathtub as well as place the brand-new bath tub, the job is much harder. In either instance, the project is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub as well as embeded in the brand-new one. Make certain you have actually qualified yourself for the job and also are comfortable attempting it. Rather than working with a service provider to take over a halfway-completed task, it is far better to consider utilizing one before you begin. Opportunities are you may need a specialist plumber to make tube links.
This post will certainly assist you mount a new bathtub in your restroom if you have already acquired a brand-new bathtub as well as do not need to change the setup of your previous water system pipelines.
Your tools and also material list should consist of the following:
Getting ready for the Installation
Firstly, the supporting structure provided with the bathroom must be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to make certain that if the faucet features a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps unit to prevent pressure on the tub.
Fit the flexible tap adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you utilize all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should now prepare to be suited its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of removing the existing taps can be quite problematic due to the limited accessibility that is typically the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will come from the pipes. As soon as the supply pipelines have been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Using both wood boards under its feet, place the tub in the needed placement. The wooden boards are helpful in evenly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the tub till the level checks out level.
To install faucets, fit all-time low of the outermost flexible tap connector to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other tap.
Turn on the water system and examine all joints as well as brand-new pipework for leakages as well as tighten them if required. Fill the tub as well as also examine the overflow outlet as well as the typical electrical outlet for leakages.
Lastly, fix the bath paneling as defined in the maker's instruction manual. Tiling and securing around the bath tub needs to wait until the bathtub has been made use of at least once as this will certainly resolve it right into its final position.
Fitting New Taps
If the tails of the new faucets are plastic, then you will need a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin making sure that the washers remain in location in between the tap and also the sink. Protect the faucet in position with the maker provided backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The former kind needs to be connected to the tap finishes initially, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall between the bathroom and also the tiling, leading to issues with wetness and possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly fill up the bathtub with water before sealing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture relatively very early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently readily available on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

We had been brought to that editorial about Installing A Bathtub through an associate on our other website. Loved our piece? Please share it. Let other people locate it. I value reading our article about How to Install a Bathtub.
Booking Report this page